A to Z Pipe Fabrication Abbreviations
Every engineering field has its list of abbreviations to help convey information quickly and easily. Here is such list of abbreviations related to piping engineering. All piping engineers should know/learn about all these abbreviations used in the piping industry to easily recognize and understand the item. In this article, we will learn some of the most frequently used common piping abbreviations. Hope it will be useful to new entrants as well as professionals alike.
1) ANSI : American National Standards Institute Inc
2) API : American Petrolium Institute
3) ASA : American Standards Association
4) Asb : Asbestos (Gaskets)
5) ASME : The American Society of Mechanical Engineers
6) ASTM : The American Society for Testing and Materials
7) AWWA : American Water Works Association
8) BBE : Bevel both ends
9) Bbl : Barrel
10) Bdr : Bleed ring
11) BE : Beveled end
12) Bfy : Butterfy (valve)
13) Bld : Blind (flange)
14) Bld : Spectacle blind (blate between flanges)
15) BLE : Bevel large end
16) Blk : Black (pipe)
17) BOE : Bevel one end
18) BOM : Bill of materials
19) BOP : Bottom of pipe
20) Brz : Bronze (valve)
21) BSE : Bevel small end
22) BW : Buttweld
23) Chk : Check (valve)
24) CI : Cast iron
25) Cm : Centimeter
26) Conc : Concentric
27) Cpl : Coupling
28) CS : Cast steel, carbon steel, cap screw
29) CSC : Car seal closed
30) Csg : Casing
31) CSO : Car seal open
32) Csw : Concentric swage
33) Cu : Cubic
34) CW : Chain wheel
35) CWO : Chain wheel operator
36) CWP : Cold water pressure
37) D&T : Drill and tap
38) D&W : Doped and wrapped (pipe)
39) DES : Double extra strong
40) DI : Ductile iron
41) Dia : Diameter
42) Dim : Dimension
43) Ditto : Do not use this term
44) DSAW : Double sub-merged arc welded (pipe)
45) Dwg # : Drawing number
46) Ea. : Each
47) Ecc : Eccentric
48) El : Elevation (on drawing)
49) Elec : Electrical
50) Ell : Elbow
51) Eol : Elbolet
52) ERW : Electric resistance weld (pipe)
53) Esw : Eccentric swage
54) EUE : External upset ends
55) Ex.hvy : Extra heavy
56) Ex.stg : Extra strong
57) Exp jt : Expansion joint
58) F&D : Faced and drilled (flanged)
59) F/F : Face of flange
60) FAB : Fabricate/fabricator
61) FAS : Free along side
62) FE : Flanged ends / flow element
63) Fem : Female (ends)
64) FF : Flat/full face
65) Fig : Figure (number)
66) Flex : Flexitallic (gasket brand name)
67) Flg. : Flange
68) Flgd : Flanged ends / flow element
69) FOB : Free on board
70) FS : Forged steel
71) FSD : Flat side down
72) FSU : Flat side up
73) Ft : Feet/foot
74) FW : Field weld/fire water
75) Gal : Gallon
76) Galv : Galvanised
77) GG : Gauge glass
78) GJ : Ground joint (union)
79) Glb : Globe (valve)
80) GR : Grade
81) Gsk : Gasket
82) HC : Hose coupling
83) Hdr : Header
84) Hex : Size-sided head, bolt, plug etc.
85) HN : Heat number
86) Hvy : Heavy
87) IBBM : Iron body bronze mounted(valve)
88) ID : Inside diamter
89) ID : Inside diamter
90) Insi : Insulation
91) IPS : Iron pipe size
92) IS&Y : Inside screw & yoke (valve)
93) ISO : Isometric (drawing)
94) IUE : Internal upset ends
95) Jkscr : Jack screw
96) Jt (s) : Jt. (joints)
97) JW : Jacket water
98) Lati : Lateral
99) Lb (s). # : Pound (s) # symbol for pounds
100) Lg : Length, long, level gauge
101) Lin Ft : Liner feet
102) LJ : Lap joint (flange)
103) LLC : Liquid level controller
104) LOL : Latrolet
105) LP : Line pipe
106) LR : Long radius
107) M : Meter/one thousand
108) M&F : Male and female (ends)
109) MAT’L : Materials
110) Max : Maximum (a warehouse stocking level)
111) MFD : Mechanical flow diagram
112) Mfg : Manufacturer
113) MI : Malleable iron
114) Min : Minimum (a warehouse stocking level)
115) Misc : Miscellaneous (schedules of pipe)
116) Mk : Mark (spool piece)
117) MM : Millimeter
118) MRR : Materials receiving report
119) MSS : Manufacturers Standards Society of the Valve and Fittings Industry
120) MTO : Material take-off (from drawings)
121) NC : Normally closed
122) Nip : Nipple (pipe)
123) No or # : Number
124) NPS : Nominal pipe size
125) NPT : Nominal pipe thread
126) NU : Non-upset (ends)
127) OD : Outside diamter
128) Orf : Orifice
129) OS&D : Over short and damage (report)
130) OS&Y : Outside screw and yoke (valve)
131) Oz : Ounce
132) P&ID : Piping and instrumentation diagram
133) PBE : Plain both ends
134) Pc : Piece (mark for spool pieces)
135) Pdl : Paddle (a blind plate between flanges)
136) PE : Plain ends
137) PI : Pressure indicator (valves & gauge assembly)
138) PLE : Plain large end
139) Plt : Plat (steel)
140) PO # : Purchase order or number
141) POE : Plain one end
142) Pr : Pair of items
143) Press : Pressure
144) PS : Pipe support
145) PSE : Plain small end
146) psi : Pounds per square inch
147) psig : Pounts-force suqre inch, guage
148) PSV : Pressure safety (relief) valve
149) PVC : Poly vinyl chloride
150) PVF : Pipe, valves and fittings
151) PW : Potable wter
152) Qty : Quantity
153) Rad : Radius
154) Rdcr : Reducer
155) Rec’d : Received (materials)
156) Red : Reducer
157) Reqn : Requisition
158) REV : Revision
159) RF : Raised face
160) RPM : Revolutions per minute
161) RR : Red rubber (gasket type)
162) RS : Rising stem (valve)
163) RTE : Reducing tee
164) Rtg : Rating
165) RTJ : Ring type joint (flange facing)
166) S/40 : Schedule 40 (of pipe or fittings)
167) SC : Sample connecitons
168) Sch : Schedule (of pipe or fittings)
169) Scrd : Screwed (ends)
170) Sdl : Saddle (pipe)
171) SE : Screwed ends
172) Skt Bld : Skillet blind (plate between flanges)
173) Smls : Seamless spec
174) SO : Slip-on (flange)
175) SOL : Sockolet
176) SPEC : Specification
177) Spl Sht : Spool sheet (from isometric drawing)
178) Sq : Square feet, yards etc.
179) SR : Short radius, stress relieve
180) SRL : Short radius ell
181) SS : Stainless steel
182) Std : Standard (a pipe or fitting schedule)
183) STD : Standard (a pipe or fitting schedule)
184) Stl : Steel
185) Stm : Steam
186) Sub : Short length of pipe or rod
187) SW : Socket weld
188) Swg : Swage nipple
189) SWP : Safe working pressure
Sr.) Abbreviation : Description
190) T&C : Threaded and coupled
191) T&G : Tongue and groove (flange facing)
192) Tbg : Tubing
193) Thk : Thick
194) Thr’d : Threaded
195) TI : Temperature indicator
196) TLE : Thread large end
197) TOE : Thread one end
198) TOL : Threadolet
199) TSE : Thread small end
200) TW : Thermometer well
201) Typ : Typical (repeat the same item)
202) Un : Union
203) VA : Valve
204) Vac : Vacuum
205) Vol : Volume
206) Wd : Width/wide
207) WE : Weld end
208) WI : Wrought iron
209) WN : Weld neck (flange)
210) WOL : Weldolet
211) WP : Working pressure
212) WT : Wall thickness/weight
213) XR : X-ray (at pipe welds)
214) XS : Extra strong
215) XXS : Double extra strong
216) Yd : Yard
0 Comments